Cisco Systems BEFSR41 Manual do Utilizador Página 23
- Página / 72
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
17
Chapter 5: Configuring the Router
The Setup Tab - Basic Setup
EtherFast Cable/DSL Router with 4-Port Switch
Router IP
The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default
values will work.
Local IP Address. The default value is 192.168.1.1.
Subnet Mask. The default value is 255.255.255.0.
Network Address Server Settings (DHCP)
These settings allow you to configure the Router’s Dynamic Host Configuration Protocol (DHCP) server function. A
DHCP server automatically assigns an IP address to each computer on your network. Unless you already have
one, it is highly recommended that you leave the Router enabled as a DHCP server.
Local DHCP Server. DHCP is enabled by factory default. If you already have a DHCP server on your network, set
the Router’s DHCP option to Disable. If you disable DHCP, remember to assign a static IP address to the Router.
Start IP Address. Enter a value for the DHCP server to start with when issuing IP addresses. Because the default
IP address for the Router is 192.168.1.1, the Start IP Address must be 192.168.1. 2 or greater, but smaller than
192.168.1.254. The default Start IP Address is 192.168.1.100.
Number of Addresses (Optional). Enter the maximum number of PCs that you want the DHCP server to assign IP
addresses to. This number cannot be greater than 253. The default is 50.
DHCP Address Range. The range of dynamic IP addresses is displayed here.
Client Lease Time. The Client Lease Time is the amount of time a network user will be allowed connection to the
Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased”
this dynamic IP address. After the dynamic IP address has expired, the user will be automatically assigned a new
dynamic IP address. The default is 0 minutes, which means one day.
Static DNS 1-3. The Domain Name System (DNS) is how the Internet translates domain or website names into
Internet addresses or URLs. Your ISP will provide you with at least one DNS Server IP Address. You can enter up to
two DNS Server IP Addresses here. The Router will use these for quicker access to functioning DNS servers.
WINS. The Windows Internet Naming Service (WINS) converts NetBIOS names to IP addresses. If you use a WINS
server, enter that server’s IP address here. Otherwise, leave this field blank.
When you have finished making changes to this screen, click the Save Settings button to save the changes, or
click the Cancel Changes button to undo your changes. Help information is shown on the right-hand side of the
screen. For additional help, click More.
dynamic ip address: a temporary IP
address assigned by a DHCP server
Note: To test your settings, connect to the
Internet now.
- Cable/DSL Router 1
- Copyright and Trademarks 2
- How to Use this Guide 2
- Table of Contents 3
- Frequently Asked Questions 49 4
- List of Figures 5
- Chapter 1: Introduction 7
- What’s in this Guide? 8
- Chapter 2: Networking Basics 10
- The Use of IP Addresses 11
- The Back Panel 12
- The Front Panel 13
- Overview 14
- Connection Instructions 15
- Applications & Gaming 17
- Administration 17
- The Setup Tab - Basic Setup 18
- Static IP 19
- Heart Beat Signal 21
- Network Setup 22
- Router IP 23
- The Setup Tab - DDNS 24
- MAC Clone 25
- Advanced Routing 26
- The Security Tab - Filter 28
- The Security Tab - VPN 30
- Port Range Forwarding 31
- Port Triggering 32
- UPnP Forwarding 33
- Device Priority 36
- Ethernet Port Priority 36
- Application Priority 36
- Router Access 38
- The Administration Tab - Log 40
- Factory Defaults 41
- Upgrade Firmware 42
- The Status Tab - Router 43
- Local Network 44
- Appendix A: Troubleshooting 45
- For Windows 2000: 46
- For Windows XP: 46
- Common Problems and Solutions 48
- For Netscape 4.7 or higher: 52
- Frequently Asked Questions 55
- Your Ethernet Adapter 60
- Appendix D: Windows Help 62
- Appendix E: Glossary 63
- Appendix F: Specifications 68
Manuais e produtos relacionados com Redes Cisco Systems BEFSR41
Redes Cisco Systems WC-293 Manual do Utilizador
(30 páginas)
(30 páginas)
Redes Cisco Systems 4/8xFE Guia do Utilizador
(131 páginas)
(131 páginas)
Redes Cisco Systems MGX 8000 Manual do Utilizador
(12 páginas)
(12 páginas)
ASROCK SBC-210 manuals
Owner’s manuals and user’s guides for Motherboards ASROCK SBC-210.
We providing 1 pdf manuals ASROCK SBC-210 for download free by document types: User Manual
Comentários a estes Manuais