Cisco Systems CISCO7206 Guia de Início Rápido

Cisco 7206 Router Quick Start Guide1 Documentation and Resources2 Prepare for Installation3 Rack-Mount the Router4 Connect the Router to the Network5

10Brackets Rear-Mounted—Front Recessed in the Rack1. Locate the threaded screw holes in the rear sides of the chassis.2. Align the first rack-mount br

11Chassis Ground Connection InstallationNote The grounding lug and Phillips-head screws are not available from Cisco Systems. Get the grounding lug fr

124 Connect the Router to the NetworkI/O Controller Console and Auxiliary Port Cable ConnectionsNote Both the console and auxiliary ports are asynchr

13Ethernet Port ConnectionsI/O controllers have the possibility of one or two types of Ethernet connections: MII connections and RJ-45 connections for

145 Start and Configure the RouterPower Cable ConnectionsWarningThis unit might have more than one power cord. To reduce the risk of electric shock,

151. At the rear of the router, check that the power switch is in the off (O) position.2. Ensure that the –V and +V leads are disconnected from the po

16Observing System Startup and Performing a Basic ConfigurationCheck conditions prior to system startup:1. Check that all hardware parts and cables ar

17Performing a Basic Configuration Using the Setup Facility If you do not plan to use AutoInstall, do not connect the router’s serial (WAN) cable to t

1820480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).4096K bytes of Flash internal SIMM (Sector size 256K).Configuration register is 0x0No

198. For the following queries, enable routing on AppleTalk and IPX:Configure AppleTalk? [no]: yes Multizone networks? [no]: yesConfigure IPX? [no]

21 Documentation and ResourcesThis section contains information to help you prepare for installing the Cisco 7206 router. I contains a list of online

20Configuring InterfacesFollowing are the steps for configuring interfaces to allow communication over a LAN or WAN. To configure the interface parame

21The following sample display includes a continuous listing of all interface configuration parameters selected for Ethernet and synchronous serial in

22!endUse this configuration? [yes/no]: yes[OK]Use the enabled mode ‘configure’ command to modify this configuration.Press RETURN to get started! Your

23Performing Complex ConfigurationsAfter you have installed your Cisco 7206 router hardware and minimally configured the system, you might need to per

246 After InstallationThis section contains hardware replacement instructions and information about contacting the Technical Assistance Center.Note T

25Replace the I/O ControllerNote Before powering down the router, use the copy running-config tftp command to save the router’s running configuration

26Replace the Flash Memory Card or Flash DiskNote Flash memory cards and Flash Disks are replaceable while the system is operating.12. Remove the Flas

27Replace a Port Adapter or Service Adapter1. To remove a port adapter, place the port adapter lever in the unlocked position (2).2. Grasp the handle

28Caution Do not mix power supplies in Cisco 7206 routers. In dual power supply configurations, both power supplies must be of the same type (two AC-i

297 Technical AssistanceCisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, t

3Port Adapter Documentation• Cisco 7200 Series Port Adapter Hardware Configuration Guidelines—DOC-783471=(This document provides bandwidth point infor

30If you cannot resolve your technical issues by using the Cisco TAC Web Site, and you are a Cisco.com registered user, you can open a case online by

31

Corporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAwww.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-

4Ordering DocumentationCisco documentation is available in the following ways:• Registered Cisco.com users (Cisco direct customers) can order Cisco pr

52 Prepare for InstallationWarning Only trained and qualified personnel should install, replace, or service this equipment.Warning Read the installat

6• Port adapter documentation for configuring the interfaces• T1 channel service unit/data service unit (CSU/DSU) that converts the High-Level Data Li

73 Rack-Mount the RouterBrackets Front-Mounted—Chassis Protrudes from the RackLocate the rack-mount and cable-management brackets and screws (1, 2, 3

8Brackets Front-Mounted—Chassis Recessed in RackLocate the rack-mount and cable-management brackets and screws (1, 2, 3 in the illustration above) and

9Brackets Rear-Mounted—Front Protrudes from the Rack1. Locate the threaded screw holes in the rear sides of the chassis.2. Align a rack-mount bracket