Cisco Systems PA-4T Manual do Utilizador

170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comCisco Systems, Inc.Corporate HeadquartersTel:800 553-NETS (6387)408 526-4000Fax: 40

Cables and PinoutsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-8EIA/TIA-449 ConnectionsThe router end of all EIA/TIA-449 ada

Overview 1-9PA-4T+ Port Adapter Cable PinoutsX.21 ConnectionsThe router end of all X.21 adapter cables is a high-density 60-pin plug. The network end

Cables and PinoutsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-10Table 1-2 EIA/TIA-232 Adapter Cable SignalsDTE Cable (CAB-2

Overview 1-11PA-4T+ Port Adapter Cable PinoutsTable 1-3 Intermediate Adapter Cable Signals (for Connecting a PA-4T+ to aNEC - NEXTSTAR 1E Model C4969

Cables and PinoutsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-12Table 1-4 EIA/TIA-449 Adapter Cable SignalsDTE Cable (CAB-4

Overview 1-13PA-4T+ Port Adapter Cable PinoutsTable 1-5 EIA-530 DTE Adapter Cable Signals (CAB-530MT=)Router End, HD160-Position Plug1 HD = high dens

Cables and PinoutsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-14Table 1-6 V.35 Adapter Cable SignalsDTE Cable (CAB-V35FT= o

Overview 1-15LEDsLEDsThe PA-4T+ contains the enabled LED, standard on all port adapters, and one status LED for eachport. After system initialization

LEDsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-16If any of the above conditions are not met, or if the initialization fail

Preface vPrefaceThis preface describes the objectives and organization of this document and explains how to findadditional information on the PA-4T+ p

Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco CertifiedInternetwork E

Document OrganizationPA-4T+ Synchronous Serial Port Adapter Installation and ConfigurationviDocument OrganizationThis document is organized into the f

Preface viiCisco Connection Online• For hardware installation and maintenance information on the Cisco 7100 series routers, refer tothe Cisco 7100 Se

Documentation CD-ROMPA-4T+ Synchronous Serial Port Adapter Installation and ConfigurationviiiYou can access CCO in the following ways:WWW: http://www.

CHAPTER Preparing for Installation 2-12Preparing for InstallationThis chapter describes the general equipment, safety, and site preparation requiremen

Software and Hardware RequirementsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration2-2Software and Hardware Requirementslists the

Preparing for Installation 2-3Software and Hardware RequirementsNote The minimum recommended VIP2 model is a VIP2-15.

Safety GuidelinesPA-4T+ Synchronous Serial Port Adapter Installation and Configuration2-4Safety GuidelinesThis section provides safety guidelines that

Preparing for Installation 2-5Electrical Equipment GuidelinesAdvarsel Dette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til

FCC Class B CompliancePA-4T+ Synchronous Serial Port Adapter Installation and Configuration2-6Preventing Electrostatic Discharge DamageElectrostatic d

Preparing for Installation 2-7FCC Class B Compliance• Move the equipment farther away from the television or radio.• Plug the equipment into an outle

CHAPTER Overview 1-11OverviewThis chapter describes the PA-4T+ port adapter and describes its LEDs, cables, and receptacles. Thischapter contains the

FCC Class B CompliancePA-4T+ Synchronous Serial Port Adapter Installation and Configuration2-8

CHAPTER VIP2 and the PA-4T+ Port Adapter 3-13VIP2 and the PA-4T+ Port AdapterThis chapter provides information on the PA-4T+ port adapter and its use

Installation OverviewPA-4T+ Synchronous Serial Port Adapter Installation and Configuration3-2Figure 3-1 VIP2-15 or VIP2-40 with a PA-4T+ in Port Adapt

VIP2 and the PA-4T+ Port Adapter 3-3Removing a Port AdapterRemoving a Port AdapterThis section provides the standard procedures for removing a port a

Installing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration3-4Figure 3-3 Location of Port Adapter Screw—Partial Por

VIP2 and the PA-4T+ Port Adapter 3-5Installing a Port AdapterFigure 3-5 Aligning a Port Adapter in a Port Adapter SlotStep 2Before you insert the new

Installing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration3-6Figure 3-6 Port Adapter Installed in a Port Adapter S

CHAPTER Cisco 7200 Series and the PA-4T+ Port Adapter 4-14Cisco 7200 Series and thePA-4T+ Port AdapterThis chapter provides information on the PA-4T+

Removing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration4-2When a port adapter slot is not in use, a blank port ad

Cisco 7200 Series and the PA-4T+ Port Adapter 4-3Installing a Port AdapterFigure 4-3 Handling a Port AdapterStep 6Place the port adapter on an antist

Port Adapter OverviewPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-2Figure 1-2 PA-4T Port Adapter—Faceplate ViewThe following

Installing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration4-4Step 5 With the port adapter halfway in the slot, con

CHAPTER Cisco uBR7200 Series and the PA-4T+ Port Adapter 5-15Cisco uBR7200 Series and thePA-4T+ Port AdapterThis chapter provides information on the P

Removing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration5-2Note The Cisco uBR7200 series supports online insertion

Cisco uBR7200 Series and the PA-4T+ Port Adapter 5-3Removing a Port Adapter• For the Cisco uBR7223, place the port adapter lever in the unlocked posi

Installing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration5-4Step 6 Place the port adapter on an antistatic surfac

Cisco uBR7200 Series and the PA-4T+ Port Adapter 5-5Installing a Port AdapterNote If the retention clip does not slide up to the locked position, the

Installing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration5-6This completes the procedure for installing a port ad

CHAPTER Cisco 7100 Series and the PA-4T+ Port Adapter 6-16Cisco 7100 Series and thePA-4T+ Port AdapterThis chapter provides information on the PA-4T+

Removing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration6-2Figure 6-2 Cisco 7140 Series Router—Port Adapter Slot 4

Cisco 7100 Series and the PA-4T+ Port Adapter 6-3Installing a Port AdapterFigure 6-3 Handling a Port AdapterStep 6Place the port adapter on an antist

Overview 1-3Synchronous Serial OverviewThe following example of the show diag slot command shows a PA-4T+ in port adapter slot 1 in aCisco 7200 serie

Installing a Port AdapterPA-4T+ Synchronous Serial Port Adapter Installation and Configuration6-4Figure 6-4 Aligning the Single-Width Port Adapter Bet

CHAPTER Installing the PA-4T+ Interface Cables 7-17Installing the PA-4T+ Interface CablesTo continue your PA-4T+ port adapter installation, you must i

Replacing PA-4T+ Port Adapter CablesPA-4T+ Synchronous Serial Port Adapter Installation and Configuration7-2Caution Serial interface cables must be at

Installing the PA-4T+ Interface Cables 7-3Replacing PA-4T+ Port Adapter CablesFollowing is an example of the show controllers cbus command for a VIP2

Replacing PA-4T+ Port Adapter CablesPA-4T+ Synchronous Serial Port Adapter Installation and Configuration7-4For a Cisco 7100 series, Cisco 7200 series

CHAPTER Configuring the PA-4T+ Interfaces 8-18Configuring the PA-4T+ InterfacesTo continue your PA-4T+ port adapter installation, you must install the

Identifying Port Adapter Slot and PA-4T+ Interface Port NumbersPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-2The system prom

Configuring the PA-4T+ Interfaces 8-3Cisco 7200 Series and Cisco uBR7200 Series PortsFigure 8-1 PA-4T+ Interface Port Address Example—Cisco uBR7246Fi

Identifying Port Adapter Slot and PA-4T+ Interface Port NumbersPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-4VIP2 PortsIn th

Configuring the PA-4T+ Interfaces 8-5Cisco 7100 Series PortsCisco 7100 Series PortsIn Cisco 7100 series routers, the slot number is the location in t

Serial Interface SpecificationsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-4EIA/TIA-449. Like EIA/TIA-449, EIA-530 refers t

Shutting Down an InterfacePA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-6Step 2 At the privileged-level prompt, enter configur

Configuring the PA-4T+ Interfaces 8-7Shutting Down an InterfaceFor a Cisco 7200 series, Cisco uBR7200 series, or Cisco 7100 series router, use thefol

Performing a Basic ConfigurationPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-8Performing a Basic ConfigurationFollowing are i

Configuring the PA-4T+ Interfaces 8-9Configuring Timing (Clock) SignalsStep 9 When you have included all of the configuration subcommands to complete

Configuring Timing (Clock) SignalsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-10Note Cisco IOS Release 11.2(7a)P or later,

Configuring the PA-4T+ Interfaces 8-11Setting the Clock RateWhen the PA-4T+ interface is a DTE, the invert-txc command inverts the TxC signal it rece

Configuring Half-Duplex and Binary Synchronous CommunicationsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-12Configuring CRCsC

Configuring the PA-4T+ Interfaces 8-13Configuring Half-DuplexConfiguring Half-DuplexUse the half-duplex command to configure PA-4T+ interfaces for half

Checking the ConfigurationPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-14Table 8-1 Half-Duplex Timer Default SettingsConfigur

Configuring the PA-4T+ Interfaces 8-15Using show Commands to Display Interface InformationUsing show Commands to Display Interface InformationTo disp

Overview 1-5Cables and PinoutsTable 1-1 Standards for Transmission Speed Versus DistanceBalanced drivers allow EIA/TIA-449 signals to travel greater

Checking the ConfigurationPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-16The following example of the show interfaces serial

Configuring the PA-4T+ Interfaces 8-17Using show Commands to Display Interface InformationThe show version (or show hardware) command displays the co

Checking the ConfigurationPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-18VIP2 show interfaces CommandFollowing are examples

Configuring the PA-4T+ Interfaces 8-19Using show Commands to Display Interface InformationThe following example of the show interfaces serial slot/po

Checking the ConfigurationPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-20The show version (or show hardware) command display

Configuring the PA-4T+ Interfaces 8-21Using ping and loopback CommandsUse the show diag command to view all the interface types installed in your sys

Checking the ConfigurationPA-4T+ Synchronous Serial Port Adapter Installation and Configuration8-22Following is an example of a successful ping comman

Cables and PinoutsPA-4T+ Synchronous Serial Port Adapter Installation and Configuration1-6• EIA/TIA-449: DTE mode with a 37-pin D-shell plug (CAB-449M

Overview 1-7PA-4T+ Receptacles and CablesEIA/TIA-232 ConnectionsThe router end of all EIA/TIA-232 adapter cables is a high-density 60-pin plug. The n